method of sewing Samosa salwar

This is my trial of samosa salwar. To the best of my knowledge this online tutorial for Samosa salwar is the first of its kind. Samosa salwar has two flaps one covering the other. When I started to think about the method of sewing samosa salwar, the first thing that came to my mind was “Tulip skirt”. Tulip skirt is a wraparound skirt where one flap covers the other. I applied the same method to each leg piece of salwar . The result was good! Here is the method that I followed.
Preparation of draft (Figure 1)

Waist piece
Draw a rectangle PQRS having side P-S on fold
P-Q= ½ seat +3½ “
P-S =7” for adults and for children ⅟₆th seat +½”
Leg piece
Draw A-B = ½ of P-Q
From B draw a line B-C perpendicular to A-B such that B-C = full length – waist piece length + 1”
From the point C draw line C-D perpendicular to B-C such that D-C =½ ankle round
On the line B-C mark point F such that ⅟₆ th seat round + 1”
From the point F draw a perpendicular line to B-C.
From point A draw a perpendicular line to A-B.
The perpendicular lines drawn from the point A and B meet at point G.
Produce F-G to E such that E-G = 2”
Join E-D.
Join the points E and A by a curved line as shown in figure.
Cut along the lines A-B-F-C-D-E-A and remove the draft.
[FONT=&quot]Using this draft as basis flaps of samosa salwar can be prepared
[/FONT]

Inner flap (Figure 2)

Step 1
Place the draft on a folded sheet of paper such that B-C falls on the fold line.
Mark the outline and cut along the outline
Duplicate draft is got
Step 2
Join H-C by a curved line as shown.
Step 3
Cut only the top layer along the line H-C
Step 4
Open the top layer.
B-H-C is the inner layer which is covered by the upper layer.
A-B-C-D-E-A is back of the salwar leg piece. You can have pleats at the back or you can leave it plain. I am showing here how to stitch with pleats at the back also.
Inner flap continued (Figure 3)




Step 5
Draw lines on the back of the leg piece draft .Cut along the lines.
Step 6
Draft can be spread like this.
Step 7





Spread the daft on a sheet of brown paper and mark out line. Cut along the line
Make a notch at the point B


Preparation of upper flap (Figure 5)







Step 1
Once again place the original draft on a sheet of news paper mark the outline.
Step 2
Cut along the line and get a duplicate draft.
Step 3
Join B-D by a curved line as shown and cut along the line.
Step 4
We use this draft to get front upper flap

continued in figure 6

 

Step 5
Draw lines from top to bottom as shown in the figure
Step 6
[FONT=&quot]Cut along the lines keeping bottom portion intact[/FONT]



Step 7
Spread this draft on a sheet of brown paper and secure with pins. Mark the outline and cut and remove the draft.
Step 8
This is the draft of front upper flap

Fabric cutting





Place the draft on the fabric of your choice and cut the pattern piece. Make a notch at the point B.

STITCHING


Figure 9
Finish the curves B-D of the upper flap and H-D of inner flap with piping with contrast fabric or with lace.
Figure 10



Place the draft of inner flap wrong side up and fold and press along the line B-C as shown

continued

 

Re: method of sewing Samosa salwar continued



Mark point X on the curve A-B of upper flap such that A-X = 1" Pin point B of the upper flap to point B of the inner flap and point X of the upper flap on point H of the inner flap.

Figure 12


Curve X-B of the upper flap is pleated and stitched to H-B of the inner flap.

Figure 13.


Keeping right sides together stitch side E-D of the upper flap to side E-D of the inner flap.

Stitch the other leg piece also in the same manner.
[FONT=&quot]Join both the leg pieces stitching along the crotch line[/FONT]



Prepare the waist piece as in the case of “Salwar with waist band”
Stitch the waist band to the leg piece such that flaps come to the front.
Pass draw string through the casing of the waist band.
Now samosa salwar is ready to wear

 

I had problem while uploading this tutorial. please delete this

 

I had omitted one step. If you do not want pleats at the back skip step 5 and use the draft as in step 4 and continue sewing.